{"title":"Cisco Meraki MR74, MR84 Outdoor Wi-Fi 5 (802.11ac) Access Points - Refurbished, Used","description":"\u003cp\u003eCisco Meraki MR74 and MR84 outdoor Wi-Fi 5 (802.11ac Wave 2) access points are the lowest-cost way to bring Meraki Wi-Fi to parking lots, yards, campuses and warehouses. They cost a fraction of a current outdoor Meraki model, often less than the antennas they connect to, and they still work. NetworkTigers sells them refurbished or used, sold unclaimed, tested by our technicians and backed by a 365-day warranty.\u003c\/p\u003e\n\n\u003ch2\u003eWhy buy these now\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrice.\u003c\/strong\u003e The lowest-cost outdoor Meraki access points we sell.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eYour antennas carry forward.\u003c\/strong\u003e MR74 antennas also fit the Wi-Fi 6 MR76, and MR84 antennas also fit the Wi-Fi 6 MR86, so antennas bought today still fit when you upgrade.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLower power.\u003c\/strong\u003e The MR74 runs on basic 802.3af PoE at 11 W. The MR84 draws 21 W on 802.3at, less than the MR86's 30 W.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnough for most outdoor areas.\u003c\/strong\u003e Outdoor coverage usually serves fewer devices per access point, where Wi-Fi 6 adds little.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eMR74 or MR84?\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMR74:\u003c\/strong\u003e 2x2:2 on 2.4 and 5 GHz, up to 1.3 Gbps, one Gigabit Ethernet port, 802.3af PoE (11 W). The budget choice for general outdoor coverage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMR84:\u003c\/strong\u003e 4x4:4 on 2.4 and 5 GHz, up to 2.5 Gbps, two Ethernet ports (one 2.5 Gbps multigigabit, one Gigabit), 802.3at PoE (21 W). The high-capacity choice for busy outdoor areas.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBoth have four N-type connectors for external antennas, a dedicated scanning radio, Bluetooth Low Energy, and an IP67 weatherproof rating for -40°F to 131°F (-40°C to 55°C).\u003c\/p\u003e\n\u003cp\u003eSome listings include the mounting kit. If yours does not, the MA-MNT-MR-7 (MR74) and MA-MNT-MR-10 (MR84) are available separately on this page.\u003c\/p\u003e\n\n\u003ch2\u003eCompared with the MR76 and MR86\u003c\/h2\u003e\n\u003cp\u003eThe MR76 and MR86 are Wi-Fi 6 and still supported by Meraki, and they serve crowded outdoor spaces such as stadiums more efficiently. The MR74 and MR84 cost far less and use less power. The MR84 adds a second Ethernet port that the MR86 does not have.\u003c\/p\u003e\n\n\u003ch2\u003eYes, they work, and we keep checking\u003c\/h2\u003e\n\u003cp\u003eThese access points still claim into a Meraki dashboard and run. We test this on an ongoing basis against the current Meraki dashboard, and every unit is bench tested by our technicians before it ships. A Meraki license is required and is sold separately; MR licenses are not tied to a model, and Meraki allows a 30-day grace period after a unit is claimed.\u003c\/p\u003e\n\n\u003ch2\u003eAntennas\u003c\/h2\u003e\n\u003cp\u003eAntennas are not included; choose them for the site. The two models take different antenna sets:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMR74:\u003c\/strong\u003e MA-ANT-20, MA-ANT-21, MA-ANT-23, MA-ANT-25 and MA-ANT-27. All five also fit the MR76.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMR84:\u003c\/strong\u003e MA-ANT-20, MA-ANT-25 and MA-ANT-27. All three also fit the MR86.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eSee all our \u003ca href=\"\/collections\/cisco-meraki-wi-fi-antennas-refurbished-used-new\"\u003eMeraki antennas\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003ch2\u003eWhat Meraki no longer provides\u003c\/h2\u003e\n\u003cp\u003eMeraki support for both models ended on July 21, 2026 (MR74 end of sale July 21, 2021; MR84 end of sale May 7, 2021). Meraki no longer provides technical support, firmware updates or warranty replacement for them, and does not guarantee dashboard connectivity indefinitely. Our 365-day NetworkTigers warranty covers every unit we sell.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is the difference between the Meraki MR74 and MR84?\u003c\/strong\u003e\u003cbr\u003eThe MR84 has 4x4 radios, a 2.5 Gbps multigigabit port plus a second Gigabit port, and needs 802.3at PoE. The MR74 has 2x2 radios, one Gigabit port, and runs on 802.3af PoE.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo the MR74 and MR84 still work now that Meraki support has ended?\u003c\/strong\u003e\u003cbr\u003eYes. They still claim into a Meraki dashboard and run, and we re-test this on an ongoing basis.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eCan I reuse my antennas if I upgrade?\u003c\/strong\u003e\u003cbr\u003eYes. MR74 antennas (MA-ANT-20, 21, 23, 25 and 27) all fit the MR76. MR84 antennas (MA-ANT-20, 25 and 27) all fit the MR86.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWill an MA-ANT-21 or MA-ANT-23 work on the MR84?\u003c\/strong\u003e\u003cbr\u003eNo. Meraki lists only the MA-ANT-20, MA-ANT-25 and MA-ANT-27 for the MR84 and MR86. The MA-ANT-21 and MA-ANT-23 are for the MR74 and MR76.\u003c\/p\u003e\n\n\u003cp\u003eSee all \u003ca href=\"\/collections\/cisco-meraki-wireless-access-points-refurbished\"\u003eMeraki wireless access points\u003c\/a\u003e, or \u003ca href=\"\/pages\/ask-for-quote\"\u003eask us for a quote\u003c\/a\u003e on larger quantities.\u003c\/p\u003e","products":[{"product_id":"mr84-hw-cisco-wi-fi-5-80211ac-4x4-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-10-wireless-access-point","title":"Cisco Meraki MR84-HW Wi-Fi 5 802.11ac Ext Ant Unclaimed (Includes Mounts) WAP","description":"\u003cp\u003eThe Cisco Meraki MR84 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. Both client radios are 4x4 MU-MIMO with 4 spatial streams, for an aggregate frame rate of 2.5 Gbps, with up to 1,733 Mbps on 5 GHz and 800 Mbps on 2.4 GHz. A third dual-band radio handles WIDS\/WIPS and a fourth handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes the MA-ANT-20 dual-band omni, MA-ANT-25 dual-band patch, or MA-ANT-27 dual-band sector antennas, plus Cisco's AIR-ANT2513P4M-N four-port patch. The housing is rated IP67 for outdoor and harsh indoor sites.\u003c\/p\u003e\r\n\r\n\u003cp\u003eIt has one 2.5 Gigabit multigigabit RJ-45 port and one Gigabit RJ-45 port. Full function needs 802.3at PoE+, at 21W maximum; 802.3af runs it in a restricted mode. It weighs 3.8 lb and mounts to walls and poles with the MA-MNT-MR-10 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; for longer reach, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. The \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-mnt-mr-10-cisco-mounting-kit-for-mr84-wall-mount\"\u003eMA-MNT-MR-10 mount kit\u003c\/a\u003e fits this AP, and the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr86-hw-cisco-wireless-access-point\"\u003eMR86-HW\u003c\/a\u003e is the Wi-Fi 6 step up. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MR84-HW access point is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":37841817075887,"sku":"NSH-3938","price":129.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MR84-HW.jpg?v=1664858220"},{"product_id":"ma-ant-23-cisco-24ghz-sector-antenna-11-dbi-antenna-new","title":"NEW Cisco Meraki MA-ANT-23 2.4GHz 11 dBi Sector Antenna for MR74 and MR76 APs","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-23 is a 2.4 GHz sector antenna for Meraki outdoor access points with N-type antenna connectors. It covers 2.400 to 2.500 GHz with 11 dBi of gain and a 70-degree horizontal beamwidth, and connects through two N-type ports with two 12-inch N cables included.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, so one access point can reach clients further away in that direction than an omni antenna can. It suits long building faces, sports fields, and parking areas covered from a single mounting point. The antenna measures 9.2 x 5.5 x 1.6 inches and weighs 1.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe MA-ANT-23 covers only the 2.4 GHz band, so it is normally paired with the 5 GHz MA-ANT-21 sector antenna on the same access point. Meraki lists it for the MR62, MR66, MR72, MR74, MR76, and MR86. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor the 5 GHz radio, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-21-cisco-5-ghz-13-dbi-sector-antenna\"\u003eMA-ANT-21 5 GHz sector antenna\u003c\/a\u003e. If you want one antenna for both bands, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e covers 2.4 and 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MA-ANT-23 antenna is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":38058134012079,"sku":"NSN-8233","price":264.49,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-23-new_fb0586aa-c83a-48a3-ab04-d5b65d07e9c1.jpg?v=1680566109"},{"product_id":"ma-ant-21-cisco-5-ghz-13-dbi-sector-antenna-new","title":"NEW Cisco Meraki MA-ANT-21 5 GHz 13 dBi Sector Antenna for MR74 and MR76 APs","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-21 is a 5 GHz sector antenna for Meraki outdoor access points with N-type antenna connectors. It covers 5.150 to 5.875 GHz with 13 dBi of gain and an 80-degree horizontal beamwidth, and connects through two N-type ports with two N cables included.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, so one access point can reach clients much further away in that direction than an omni antenna can. Typical uses are covering a long side of a building, a sports field, or a row of parking from a single mounting point. The antenna measures 9.2 x 5.5 x 1.6 inches and weighs 1.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe MA-ANT-21 covers only the 5 GHz band, so it is normally paired with the 2.4 GHz MA-ANT-23 sector antenna on the same access point. Meraki lists it for the MR58, MR66, MR72, and MR74. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor the 2.4 GHz radio, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-23-cisco-24ghz-sector-antenna-11-dbi-antenna\"\u003eMA-ANT-23 2.4 GHz sector antenna\u003c\/a\u003e. If you want one antenna for both bands, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e covers 2.4 and 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MA-ANT-21 antenna is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":38058196828335,"sku":"NSN-8226","price":375.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-21-new_1af39962-0b01-4f1f-9323-f003e3176156.jpg?v=1680566043"},{"product_id":"ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna","title":"Cisco Meraki MA-ANT-25 Dual Band Patch Antenna for MR74 MR76 MR84 and MR86","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-25 is a dual-band patch antenna for Meraki outdoor access points with N-type antenna connectors. It is a single antenna with two ports, one for each polarization, with 8 dBi of gain on 2.4 GHz and 6.5 dBi on 5 GHz. Horizontal beamwidth is 60 degrees on 2.4 GHz and 75 degrees on 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA patch antenna points coverage in one direction with a wider beam than a sector antenna, which makes it a good fit for mounting on a wall or pole to cover the area in front of it, such as a loading dock, an entrance plaza, or one side of a building. It measures 7.1 x 7.1 inches and weighs 1.1 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-25 for the MR66, MR72, MR74, and MR86. Because it covers both bands in one housing, it needs fewer mounting points than a pair of single-band sector antennas. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 dual-band omni antenna set\u003c\/a\u003e is the alternative. For a narrower, longer-reaching beam on both bands, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-ANT-25 antenna is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":38067654459567,"sku":"NSB-7046","price":129.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MA-ANT-25-2.jpg?v=1781609235"},{"product_id":"ma-ant-21-cisco-5-ghz-13-dbi-sector-antenna","title":"Cisco Meraki MA-ANT-21 5 GHz 13 dBi Sector Antenna for MR74 and MR76 APs","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-21 is a 5 GHz sector antenna for Meraki outdoor access points with N-type antenna connectors. It covers 5.150 to 5.875 GHz with 13 dBi of gain and an 80-degree horizontal beamwidth, and connects through two N-type ports with two N cables included.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, so one access point can reach clients much further away in that direction than an omni antenna can. Typical uses are covering a long side of a building, a sports field, or a row of parking from a single mounting point. The antenna measures 9.2 x 5.5 x 1.6 inches and weighs 1.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe MA-ANT-21 covers only the 5 GHz band, so it is normally paired with the 2.4 GHz MA-ANT-23 sector antenna on the same access point. Meraki lists it for the MR58, MR66, MR72, and MR74. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor the 2.4 GHz radio, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-23-cisco-24ghz-sector-antenna-11-dbi-antenna\"\u003eMA-ANT-23 2.4 GHz sector antenna\u003c\/a\u003e. If you want one antenna for both bands, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e covers 2.4 and 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-ANT-21 antenna is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":38138121060527,"sku":"NSB-6974","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-21_e922381c-20c6-4a49-add2-f7483a714913.jpg?v=1680566076"},{"product_id":"ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna","title":"Cisco Meraki MA-ANT-20 Dual-Band Omni Antenna Set MR72, MR74, MR76, MR86, MR84","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-20 is a dual-band omnidirectional antenna set for Meraki outdoor access points with N-type antenna connectors. The set contains two antennas, each with 4 dBi of gain on 2.4 GHz and 7 dBi on 5 GHz, with a 360-degree horizontal and 45-degree vertical beam.\u003c\/p\u003e\r\n\r\n\u003cp\u003eOmni antennas spread coverage evenly around the access point, which suits parking lots, courtyards, campus quads, and open warehouse yards where clients can be on any side. Each antenna is about 7.1 inches long and 1.0 inch in diameter and weighs about 0.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-20 for the MR58, MR62, MR66, MR72, MR74, MR76, and MR86. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eIf you need to cover one direction instead of all around, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch antenna\u003c\/a\u003e and the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e focus the signal. A compatible access point is the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr76-hw-cisco-wi-fi-6-80211ax-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-16-wireless-access-point\"\u003eMR76-HW outdoor access point\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-ANT-20 antenna set is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":39957985788079,"sku":"NSB-1417","price":98.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-20_5c2993c1-d4f5-4ddf-a898-4480827d338f.jpg?v=1680812549"},{"product_id":"ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna","title":"Cisco Meraki MA-ANT-27 Dual-Band WAP Sector Antenna for MR74 MR76 MR84 MR86","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-27 is a dual-band sector antenna for Meraki outdoor access points with N-type antenna connectors. Gain is 9 dBi on 2.4 GHz and 12 dBi on 5 GHz. Horizontal beamwidth is 86 degrees on 2.4 GHz and 65 degrees on 5 GHz, with 34 and 18 degrees vertical. It connects through two N-type ports with two 12-inch cables.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, which extends range in one direction. Because the MA-ANT-27 covers both bands, one antenna replaces the pair of single-band MA-ANT-21 and MA-ANT-23 sector antennas. It measures 9.1 x 5.5 x 1.9 inches and weighs 1.4 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-27 for the MR74 and MR84, and the MR86 data sheet also lists it. Typical uses are covering a long building face, a sports field, or a parking area from a single pole. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 dual-band omni antenna set\u003c\/a\u003e is the alternative. For a wider beam from a wall, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch antenna\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-ANT-27 antenna is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":40453285413039,"sku":"NSB-0578","price":245.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-27_8e3675e2-c362-4743-805b-6cb865482365.jpg?v=1680566275"},{"product_id":"ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna-new","title":"NEW Cisco Meraki MA-ANT-27 Dual-Band WAP Sector Antenna for MR74 MR76 MR84 MR86","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-27 is a dual-band sector antenna for Meraki outdoor access points with N-type antenna connectors. Gain is 9 dBi on 2.4 GHz and 12 dBi on 5 GHz. Horizontal beamwidth is 86 degrees on 2.4 GHz and 65 degrees on 5 GHz, with 34 and 18 degrees vertical. It connects through two N-type ports with two 12-inch cables.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, which extends range in one direction. Because the MA-ANT-27 covers both bands, one antenna replaces the pair of single-band MA-ANT-21 and MA-ANT-23 sector antennas. It measures 9.1 x 5.5 x 1.9 inches and weighs 1.4 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-27 for the MR74 and MR84, and the MR86 data sheet also lists it. Typical uses are covering a long building face, a sports field, or a parking area from a single pole. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 dual-band omni antenna set\u003c\/a\u003e is the alternative. For a wider beam from a wall, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch antenna\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MA-ANT-27 antenna is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":41528982339759,"sku":"NSN-8753","price":255.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-27-new_d4b641d5-db6c-4c25-8f61-88bf95081e45.jpg?v=1680566242"},{"product_id":"ma-ant-23-cisco-24ghz-sector-antenna-11-dbi-antenna","title":"Cisco Meraki MA-ANT-23 2.4GHz 11 dBi Sector Antenna for MR74 and MR76 APs","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-23 is a 2.4 GHz sector antenna for Meraki outdoor access points with N-type antenna connectors. It covers 2.400 to 2.500 GHz with 11 dBi of gain and a 70-degree horizontal beamwidth, and connects through two N-type ports with two 12-inch N cables included.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA sector antenna concentrates signal into a wedge in front of it, so one access point can reach clients further away in that direction than an omni antenna can. It suits long building faces, sports fields, and parking areas covered from a single mounting point. The antenna measures 9.2 x 5.5 x 1.6 inches and weighs 1.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe MA-ANT-23 covers only the 2.4 GHz band, so it is normally paired with the 5 GHz MA-ANT-21 sector antenna on the same access point. Meraki lists it for the MR62, MR66, MR72, MR74, MR76, and MR86. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor the 5 GHz radio, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-21-cisco-5-ghz-13-dbi-sector-antenna\"\u003eMA-ANT-21 5 GHz sector antenna\u003c\/a\u003e. If you want one antenna for both bands, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e covers 2.4 and 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-ANT-23 antenna is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":41702391677103,"sku":"NSB-7047","price":229.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/products\/cisco-MA-ANT-23_9854023c-872c-4051-9e26-ffb65d8c5d09.jpg?v=1680566142"},{"product_id":"ma-mnt-mr-7-cisco-replacement-outdoor-wall-and-pole-mount-kit-for-mr72-mr74-wall-mount","title":"Cisco Meraki MA-MNT-MR-7 Mounting Kit for MR72 and MR74 Wireless Access Points","description":"\u003cp\u003eThe Cisco Meraki MA-MNT-MR-7 is the replacement mounting kit for the Meraki MR72 and MR74 outdoor access points. It holds the access point on a wall or a vertical pole and is the same style of hardware Meraki ships with a new outdoor unit.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe kit includes a replacement mount plate, drop-ceiling clips with set screws, four screws with anchors, grounding screws, mounting straps for pole installs, and a cable gland. Outdoor mounts also ground the access point and seal the cable entry, so use the supplied hardware rather than an indoor bracket.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA mount kit is the usual fix when a used or refurbished outdoor access point arrives without its bracket, or when an access point is moved to a new pole or building. Brackets are model-specific, so match the kit to the access point model before ordering. Follow the Meraki installation guide for grounding and cable sealing.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe kit fits the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr74-hw-cisco-wi-fi-5-80211ac-wave-2-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-7-wireless-access-point\"\u003eMR74-HW outdoor access point\u003c\/a\u003e; for antennas on the MR74, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 dual-band omni antenna set\u003c\/a\u003e. For the MR76 and MR86, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-mnt-mr-16-cisco-mounting-kit-for-mr76-mr86-and-cw9163e-wall-mount\"\u003eMA-MNT-MR-16 mounting kit\u003c\/a\u003e is the match, and for the MR84, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-mnt-mr-10-cisco-mounting-kit-for-mr84-wall-mount\"\u003eMA-MNT-MR-10 mounting kit\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-MNT-MR-7 mounting kit is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":44542755537071,"sku":"NSB-8418","price":75.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MA-MNT-MR-7.jpg?v=1730134702"},{"product_id":"ma-mnt-mr-10-cisco-mounting-kit-for-mr84-wall-mount","title":"Cisco Meraki MA-MNT-MR-10 Mounting Kit for MR84 Access Point","description":"\u003cp\u003eThe Cisco Meraki MA-MNT-MR-10 is the replacement mounting kit for the Meraki MR84 outdoor access points. It holds the access point on a wall or a pole and is the same style of hardware Meraki ships with a new outdoor unit.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe kit includes the mounting hardware for wall and pole installation; contents are not itemized by Meraki, so check the photos for exactly what is included. Outdoor mounts also ground the access point and seal the cable entry, so use the supplied hardware rather than an indoor bracket. The MR84 box itself ships with a mount cradle, wall screws and anchors, grounding screws, and mounting straps for poles under 3.9 inches.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA mount kit is the usual fix when a used or refurbished outdoor access point arrives without its bracket, or when an access point is moved to a new pole or building. Brackets are model-specific, so match the kit to the access point model before ordering. Follow the Meraki installation guide for torque and grounding.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe kit fits the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr84-hw-cisco-wi-fi-5-80211ac-4x4-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-10-wireless-access-point\"\u003eMR84-HW outdoor access point\u003c\/a\u003e. For antennas on the MR84, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MA-MNT-MR-10 mounting kit is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":45492357169327,"sku":"NSB-8726","price":81.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MA-MNT-MR-10.jpg?v=1751373897"},{"product_id":"ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna-new","title":"NEW Cisco Meraki MA-ANT-25 Dual Band Patch Antenna for MR74 MR76 MR84 and MR86","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-25 is a dual-band patch antenna for Meraki outdoor access points with N-type antenna connectors. It is a single antenna with two ports, one for each polarization, with 8 dBi of gain on 2.4 GHz and 6.5 dBi on 5 GHz. Horizontal beamwidth is 60 degrees on 2.4 GHz and 75 degrees on 5 GHz.\u003c\/p\u003e\r\n\r\n\u003cp\u003eA patch antenna points coverage in one direction with a wider beam than a sector antenna, which makes it a good fit for mounting on a wall or pole to cover the area in front of it, such as a loading dock, an entrance plaza, or one side of a building. It measures 7.1 x 7.1 inches and weighs 1.1 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-25 for the MR66, MR72, MR74, and MR86. Because it covers both bands in one housing, it needs fewer mounting points than a pair of single-band sector antennas. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 dual-band omni antenna set\u003c\/a\u003e is the alternative. For a narrower, longer-reaching beam on both bands, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MA-ANT-25 antenna is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":45864552661167,"sku":"NSN-0642","price":223.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MA-ANT-25-new_c0347020-cfd4-4a24-a71c-75af667eedde.jpg?v=1757480980"},{"product_id":"mr84-hw-cisco-wi-fi-5-80211ac-4x4-external-antenna-unclaimed-outdoor-no-mounts-wireless-access-point","title":"Cisco Meraki MR84-HW Wi-Fi 5 802.11ac External Antenna Unclaimed (No Mounts) WAP","description":"\u003cp\u003eThe Cisco Meraki MR84 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. Both client radios are 4x4 MU-MIMO with 4 spatial streams, for an aggregate frame rate of 2.5 Gbps, with up to 1,733 Mbps on 5 GHz and 800 Mbps on 2.4 GHz. A third dual-band radio handles WIDS\/WIPS and a fourth handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes the MA-ANT-20 dual-band omni, MA-ANT-25 dual-band patch, or MA-ANT-27 dual-band sector antennas, plus Cisco's AIR-ANT2513P4M-N four-port patch. The housing is rated IP67 for outdoor and harsh indoor sites.\u003c\/p\u003e\r\n\r\n\u003cp\u003eIt has one 2.5 Gigabit multigigabit RJ-45 port and one Gigabit RJ-45 port. Full function needs 802.3at PoE+, at 21W maximum; 802.3af runs it in a restricted mode. It weighs 3.8 lb and mounts to walls and poles with the MA-MNT-MR-10 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; for longer reach, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. The \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-mnt-mr-10-cisco-mounting-kit-for-mr84-wall-mount\"\u003eMA-MNT-MR-10 mount kit\u003c\/a\u003e fits this AP, and the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr86-hw-cisco-wireless-access-point\"\u003eMR86-HW\u003c\/a\u003e is the Wi-Fi 6 step up. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MR84-HW access point is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":46524808200367,"sku":"NSC-0087","price":59.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MR84-HW-4_91656f67-504f-4120-ae65-55b9e52e970f.jpg?v=1769723534"},{"product_id":"mr74-hw-cisco-wi-fi-5-80211ac-wave-2-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-7-wireless-access-point","title":"Cisco Meraki MR74-HW Wi-Fi 5 802.11ac Ext Ant Unclaimed Outdoor WAP w\/ Mounts","description":"\u003cp\u003eThe Cisco Meraki MR74 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. It has a 2.4 GHz and a 5 GHz client radio, each 2x2 MU-MIMO with 2 spatial streams, for an aggregate data rate of 1.3 Gbps. A third dual-band radio handles WIDS\/WIPS and location analytics, and a fourth radio handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes Meraki's outdoor antennas: the MA-ANT-20 dual-band omni, the MA-ANT-21 5 GHz and MA-ANT-23 2.4 GHz sectors, the MA-ANT-25 dual-band patch, and the MA-ANT-27 dual-band sector. The housing is rated IP67.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe uplink is one 100\/1000 RJ-45 port on 802.3af PoE at 37 to 57V, with an 11W maximum draw. The unit measures 10 x 6.2 x 2.6 inches and weighs 2.4 lb. It mounts to walls and vertical poles with the MA-MNT-MR-7 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; to aim coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch\u003c\/a\u003e or \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. For Wi-Fi 6, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr76-hw-cisco-wi-fi-6-80211ax-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-16-wireless-access-point\"\u003eMR76-HW\u003c\/a\u003e. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MR74-HW access point is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":46619237744815,"sku":"NSH-3941","price":95.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MR74-HW_0d2a18f7-30c1-4bcc-916a-7e4d27621d5c.jpg?v=1772789796"},{"product_id":"mr74-hw-cisco-wi-fi-5-80211ac-wave-2-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-7-wireless-access-point-new","title":"NEW Cisco Meraki MR74-HW Wi-Fi 5 802.11ac ExtAnt Unclaimed Outdoor WAP w\/ Mounts","description":"\u003cp\u003eThe Cisco Meraki MR74 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. It has a 2.4 GHz and a 5 GHz client radio, each 2x2 MU-MIMO with 2 spatial streams, for an aggregate data rate of 1.3 Gbps. A third dual-band radio handles WIDS\/WIPS and location analytics, and a fourth radio handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes Meraki's outdoor antennas: the MA-ANT-20 dual-band omni, the MA-ANT-21 5 GHz and MA-ANT-23 2.4 GHz sectors, the MA-ANT-25 dual-band patch, and the MA-ANT-27 dual-band sector. The housing is rated IP67.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe uplink is one 100\/1000 RJ-45 port on 802.3af PoE at 37 to 57V, with an 11W maximum draw. The unit measures 10 x 6.2 x 2.6 inches and weighs 2.4 lb. It mounts to walls and vertical poles with the MA-MNT-MR-7 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; to aim coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch\u003c\/a\u003e or \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. For Wi-Fi 6, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr76-hw-cisco-wi-fi-6-80211ax-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-16-wireless-access-point\"\u003eMR76-HW\u003c\/a\u003e. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MR74-HW access point is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":47415992484015,"sku":"NSN-5188","price":199.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MR74-HW-new.jpg?v=1788039782"},{"product_id":"mr74-hw-cisco-wi-fi-5-80211ac-wave-2-external-antenna-unclaimed-outdoor-no-mounts-wireless-access-point","title":"Cisco Meraki MR74-HW Wi-Fi 5 802.11ac Wave 2 Unclaimed Outdoor WAP - NO MOUNTS","description":"\u003cp\u003eThe Cisco Meraki MR74 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. It has a 2.4 GHz and a 5 GHz client radio, each 2x2 MU-MIMO with 2 spatial streams, for an aggregate data rate of 1.3 Gbps. A third dual-band radio handles WIDS\/WIPS and location analytics, and a fourth radio handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes Meraki's outdoor antennas: the MA-ANT-20 dual-band omni, the MA-ANT-21 5 GHz and MA-ANT-23 2.4 GHz sectors, the MA-ANT-25 dual-band patch, and the MA-ANT-27 dual-band sector. The housing is rated IP67.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe uplink is one 100\/1000 RJ-45 port on 802.3af PoE at 37 to 57V, with an 11W maximum draw. The unit measures 10 x 6.2 x 2.6 inches and weighs 2.4 lb. It mounts to walls and vertical poles with the MA-MNT-MR-7 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; to aim coverage, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch\u003c\/a\u003e or \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. For Wi-Fi 6, see the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr76-hw-cisco-wi-fi-6-80211ax-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-16-wireless-access-point\"\u003eMR76-HW\u003c\/a\u003e. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis seller refurbished Cisco Meraki MR74-HW access point is tested, working, and covered by the NetworkTigers one-year warranty.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":50544508305583,"sku":"NSC-0086","price":39.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MR74-HW-3_61bb6924-c1c2-495d-bbf8-b345657d1ad2.jpg?v=1790592490"},{"product_id":"mr84-hw-cisco-wi-fi-5-80211ac-4x4-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-10-wireless-access-point-new","title":"NEW Cisco Meraki MR84-HW Wi-Fi 5 802.11ac ExtAnt Unclaimed Outdoor WAP w\/ Mounts","description":"\u003cp\u003eThe Cisco Meraki MR84 is an outdoor Wi-Fi 5 (802.11ac Wave 2) access point managed from the Meraki Dashboard. Both client radios are 4x4 MU-MIMO with 4 spatial streams, for an aggregate frame rate of 2.5 Gbps, with up to 1,733 Mbps on 5 GHz and 800 Mbps on 2.4 GHz. A third dual-band radio handles WIDS\/WIPS and a fourth handles Bluetooth Low Energy.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThe AP ships without antennas. It has four N-type female connectors and takes the MA-ANT-20 dual-band omni, MA-ANT-25 dual-band patch, or MA-ANT-27 dual-band sector antennas, plus Cisco's AIR-ANT2513P4M-N four-port patch. The housing is rated IP67 for outdoor and harsh indoor sites.\u003c\/p\u003e\r\n\r\n\u003cp\u003eIt has one 2.5 Gigabit multigigabit RJ-45 port and one Gigabit RJ-45 port. Full function needs 802.3at PoE+, at 21W maximum; 802.3af runs it in a restricted mode. It weighs 3.8 lb and mounts to walls and poles with the MA-MNT-MR-10 kit; some listings include the kit and some do not, and each listing's Model Name says which.\u003c\/p\u003e\r\n\r\n\u003cp\u003eFor all-around coverage, add the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna\"\u003eMA-ANT-20 N-type dual-band omni antenna set\u003c\/a\u003e; for longer reach, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector\u003c\/a\u003e. The \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-mnt-mr-10-cisco-mounting-kit-for-mr84-wall-mount\"\u003eMA-MNT-MR-10 mount kit\u003c\/a\u003e fits this AP, and the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr86-hw-cisco-wireless-access-point\"\u003eMR86-HW\u003c\/a\u003e is the Wi-Fi 6 step up. The access point is sold unclaimed; a Meraki license is required, purchased separately.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MR84-HW access point is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":50549179154607,"sku":"NSN-4209","price":796.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MR84-HW-new.jpg?v=1790672731"},{"product_id":"ma-ant-20-cisco-dual-band-omni-antenna-set-47-dbi-n-type-set-of-2-antenna-new","title":"NEW Cisco Meraki MA-ANT-20 Dual-Band Omni Antenna Set MR72 MR74 MR76 MR86 MR84","description":"\u003cp\u003eThe Cisco Meraki MA-ANT-20 is a dual-band omnidirectional antenna set for Meraki outdoor access points with N-type antenna connectors. The set contains two antennas, each with 4 dBi of gain on 2.4 GHz and 7 dBi on 5 GHz, with a 360-degree horizontal and 45-degree vertical beam.\u003c\/p\u003e\r\n\r\n\u003cp\u003eOmni antennas spread coverage evenly around the access point, which suits parking lots, courtyards, campus quads, and open warehouse yards where clients can be on any side. Each antenna is about 7.1 inches long and 1.0 inch in diameter and weighs about 0.2 lb.\u003c\/p\u003e\r\n\r\n\u003cp\u003eMeraki lists the MA-ANT-20 for the MR58, MR62, MR66, MR72, MR74, MR76, and MR86. Outdoor Meraki access points such as the MR74, MR76, and MR86 use N-type antenna connectors, and each external antenna connects to the matching radio port on the AP. Plan cable runs short, since longer coax adds loss that cancels some of the antenna gain.\u003c\/p\u003e\r\n\r\n\u003cp\u003eIf you need to cover one direction instead of all around, the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-25-cisco-dual-band-patch-antenna-8-and-65-dbi-n-type-antenna\"\u003eMA-ANT-25 dual-band patch antenna\u003c\/a\u003e and the \u003ca href=\"https:\/\/www.networktigers.com\/products\/ma-ant-27-cisco-dual-band-sector-antenna-9-and-12-dbi-n-type-antenna\"\u003eMA-ANT-27 dual-band sector antenna\u003c\/a\u003e focus the signal. A compatible access point is the \u003ca href=\"https:\/\/www.networktigers.com\/products\/mr76-hw-cisco-wi-fi-6-80211ax-external-antenna-unclaimed-outdoor-includes-ma-mnt-mr-16-wireless-access-point\"\u003eMR76-HW outdoor access point\u003c\/a\u003e.\u003c\/p\u003e\r\n\r\n\u003cp\u003eThis Cisco Meraki MA-ANT-20 antenna set is new and covered by the NetworkTigers one-year warranty. The original packaging may have been opened to inspect the contents.\u003c\/p\u003e","brand":"Cisco","offers":[{"title":"Default Title","offer_id":50677381267631,"sku":"NSN-9918","price":167.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/files\/cisco-MA-ANT-20-new.jpg?v=1792140833"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0989\/9318\/collections\/cisco-MR84-HW-2_d7d430c8-f6d2-4a3f-8b81-6cb6123a4d1c.jpg?v=1790440436","url":"https:\/\/www.networktigers.com\/collections\/cisco-meraki-mr74-mr84-outdoor-wi-fi-5-802-11ac-access-points-refurbished-used.oembed","provider":"NetworkTigers","version":"1.0","type":"link"}